FIREWALL BUILDER FOR LINUX MAC OS X

Objects form the foundation of the Firewall Builder GUI. The focus of this article is using Firewall Builder's cluster feature to manage a single firewall policy for the HA firewall pair, but let's start with a quick overview of a few key Firewall Builder concepts.

FIREWALL BUILDER FOR LINUX MAC OS X

Commercial licenses are available for prebuilt MS Windows and Mac OS X packages. In addition to iptables, Firewall Builder also includes support for configuring BSD pf, Cisco ASA, PIX and FWSM firewalls, Cisco router access, ipfw and ipfilter firewalls. Originally started in 2000, Firewall Builder is an open-source project with thousands of users around the world using it to manage production firewalls. SSH and SCP are used to transfer the generated firewall scripts to the remote firewalls, so it is recommended that the Firewall Builder application be run on a different workstation and not on one of the firewall servers. Multiple firewalls can be managed from a single workstation using Firewall Builder. Information about downloading and installing Firewall Builder can be found on the Firewall Builder Web site, including a Quick Start Guide (see Resources) that provides a high-level overview of the GUI layout and key concepts. Firewall Builder makes it simple to configure and maintain a synchronized set of rules on both of the HA firewall servers.įirewall Builder is a GUI-based firewall configuration management application that supports a wide range of firewalls, including iptables. Although this can be done by manually entering iptables commands, it can be difficult to maintain and is easy for errors to occur. In most HA pairs, the rules should be identical on both firewalls. Now that there are two servers configured and ready to act as HA firewalls, it's time to add rules. In this example, devices on the internal LAN that are going out through the HA firewall pair should be configured with a default gateway of 10.1.1.1.įirewall Builder Overview and Configuration When using VRRP, devices on the network should be configured to route through the virtual IP address. If the lj-fw-1 server fails, the lj-fw-2 server automatically will take over the virtual IP addresses and respond to traffic sent to it. Because the lj-fw-1 server has the highest priority number, as long as the lj-fw-1 server is “alive”, it will respond to traffic sent to the virtual IP addresses. The firewall with the highest priority number is chosen as the master. VRRP uses priority numbering to determine which firewall should be the master when both firewalls are on-line. The primary-backup.sh script, which was copied to the /etc/conntrackd directory earlier, informs conntrackd of VRRP state transitions so that conntrackd knows which firewall is currently acting as the master. The sync_group configuration includes information about the scripts to call in the event of a VRRP transition on the local server to the master, backup or fault states. This is important for Active-Backup HA firewall deployments where all the traffic must flow in and out of the same firewall. One of the benefits of keepalived is that it provides sync_groups-a feature to ensure that if one of the interfaces in the sync_group transitions from the master to the backup, all the other interfaces in the sync_group also transition to the backup. Edit the default values in this section to match the example network environment shown in Figure 1. Open the /etc/conntrackd/nf file for editing, and find the section in the file called Multicast. cd /usr/share/doc/conntrackd/examples/sync gunzip ftfw/ cp ftfw/nf /etc/conntrackd/ cp primary-backup.sh /etc/conntrackd Run the commands listed below to copy the sample config file and failover script to the default directory for conntrackd, /etc/conntrackd/nf: Garrick, shrink below. For Ubuntu, these example files are located in the /usr/share/doc/conntrackd/examples/sync/ directory. There is also a script called primary-backup.sh that provides integration between keepalived and conntrackd. This configuration uses the FTFW reliable protocol to synchronize the connection data between the firewalls. The example here is based on one of the example configuration files that comes with conntrackd. In the event of a failover, the backup firewall already will have information about the active allowed connections, so that existing connections do not have to be re-established after the failover occurs. In an Active-Backup configuration, like the example in this article, each time a connection is allowed through the active firewall, information about this connection is sent to the backup firewall. Conntrackd synchronizes the state of active connections between two or more firewalls running iptables. Conntrackd is a dæmon developed by the project, the same organization that develops iptables.

Firewall builder for linux